Precision-digital PD663 Manual do Utilizador Página 1

PRECISION DIGITAL CORPORATION 89 October Hill Road • Holliston MA 01746 USA Tel (800) 343-1001 • Fax (508) 655-8990 www.predig.com PD663 EXPLOSION-

PD663 Loop-Powered Meter Instruction Manual 10 Electromagnetic Compatibility EMISSIONS EN 61326:2006 Safety requirements for measurement, control, an

PD663 Loop-Powered Meter Instruction Manual 11 SAFETY INFORMATION WARNINGS  Read complete instructions prior to installation and operation of the

PD663 Loop-Powered Meter Instruction Manual 12 INSTALLATION For Installation in USA: The PD663 must be installed in accordance with the National Elec

PD663 Loop-Powered Meter Instruction Manual 13 Mounting The PD663 has two mounting holes that may be used for a 1.5” pipe mounting or wall mounting.

PD663 Loop-Powered Meter Instruction Manual 14 Connections (continued) See Figure 1 for terminal positions on the rear of the meter assembly. Figur

PD663 Loop-Powered Meter Instruction Manual 15 4-20 mA Input Connections & Wiring Diagrams Signal input connections are made to a three-terminal

PD663 Loop-Powered Meter Instruction Manual 16 SETUP AND PROGRAMMING There is no need to recalibrate the meter for milliamps when first received fro

PD663 Loop-Powered Meter Instruction Manual 17 Buttons and Display Button/ Symbol Description MENU Menu button to enter programming mode. Press and

PD663 Loop-Powered Meter Instruction Manual 18 Setting Numeric Values The numeric values are set using the Right and Up arrow buttons. Press the Righ

PD663 Loop-Powered Meter Instruction Manual 19 Main Menu The main menu consists of the most commonly used functions: Decimal Point Location, Scale, a

PD663 Loop-Powered Meter Instruction Manual 2 Disclaimer The information contained in this document is subject to change without notice. Precision Di

PD663 Loop-Powered Meter Instruction Manual 20 Main Menu Display Functions & Messages The meter displays various functions and messages during se

PD663 Loop-Powered Meter Instruction Manual 21 Scaling the Meter (SCL) The 4-20 mA input can be scaled to display the process in engineering units. A

PD663 Loop-Powered Meter Instruction Manual 22 Calibrating the Meter (Cal) To scale the meter without a signal source refer to Scaling the Meter (SC

PD663 Loop-Powered Meter Instruction Manual 23 Advanced Features Menu To simplify the setup process, functions not needed for most applications are l

PD663 Loop-Powered Meter Instruction Manual 24 Advanced Features Menu & Display Messages The following table shows the Advanced features menu fun

PD663 Loop-Powered Meter Instruction Manual 25 Signal Input Conditioning Function (Fnc) The PD663 provides linear and squar root signal input conditi

PD663 Loop-Powered Meter Instruction Manual 26 Internal Calibration (ICal) There is no need to recalibrate the meter for milliamps when first receive

PD663 Loop-Powered Meter Instruction Manual 27 OPERATION Front Panel Buttons Operation Button Symbol Description MENU Press to enter or exit Program

PD663 Loop-Powered Meter Instruction Manual 28 Maximum & Minimum Readings (HI & LO) The maximum and minimum (peak & valley) readings reac

PD663 Loop-Powered Meter Instruction Manual 29 Reset Meter to Factory Defaults When the parameters have been changed in a way that is difficult to de

PD663 Loop-Powered Meter Instruction Manual 3 Limited Warranty Precision Digital Corporation warrants this product against defects in material or wor

PD663 Loop-Powered Meter Instruction Manual 30 Factory Defaults & User Settings The following table shows the factory setting for most of the pro

PD663 Loop-Powered Meter Instruction Manual 31 TROUBLESHOOTING The rugged design and the user-friendly interface of the meter should make it unusual

PD663 Loop-Powered Meter Instruction Manual 32 MOUNTING DIMENSIONS All units: inches [mm] Figure 4. Enclosure Dimensions – Front View

PD663 Loop-Powered Meter Instruction Manual 33 Figure 5. Enclosure Dimensions – Side Cross Section View Note: The supplied conduit plug may extend

PD663 Loop-Powered Meter Instruction Manual 34 QUICK USER INTERFACE REFERENCE ScaleRun ModeCalibrateDisplayMax/Mindd.ddin2d1in1ddd.dddddd.dddPushbut

PD663 Loop-Powered Meter Instruction Manual 35 EC DECLARATION OF CONFORMITY Issued in accordance with ATEX Directive 94/9/EC Manufacturer: Pr

PD663 Loop-Powered Meter Instruction Manual LIM663_K SFT054 Ver 1.800 & up 12/14 How to Contact Precision Digital  For Technical Support pleas

PD663 Loop-Powered Meter Instruction Manual 4 INTRODUCTION The ProtEX-Lite PD663 is a rugged, NEMA 4X loop-powered meter in an explosion-proof enclos

PD663 Loop-Powered Meter Instruction Manual 5 Table of Contents INTRODUCTION----------------------------------------------------------------------- 4

PD663 Loop-Powered Meter Instruction Manual 6 Table of Figures Figure 1. PD663 Meter Assembly, Rear View ... 14Figu

PD663 Loop-Powered Meter Instruction Manual 7 SPECIFICATIONS Except where noted all specifications apply to operation at +25°C. General DISPLAY 0.6&

PD663 Loop-Powered Meter Instruction Manual 8 Input ACCURACY ±1 count FUNCTION Linear (2 to 32 points) or square root TEMPERATURE DRIFT 50 PPM/C f

PD663 Loop-Powered Meter Instruction Manual 9 Product Ratings and Approvals FM Class I, Division 1, Groups B, C, D Class II, Division 1, Groups E, F